Slot & Shaft
Aluminum extrusion table frame in 3030 profile with a tabletop, still image
Aluminum extrusion · Linear shaft

DIY Aluminum Extrusion Table

A table or a workbench: set the size and we list every part of the 3030 frame, sized from the manufacturer’s drawings.

Extrusion Table160 × 66 × 79 cm
Still image — the live 3D preview loads next.

Extrusion Table

3030 EU T-slot · 10 profiles · 75 parts
cm
cm
cm

Default value — change it to match your board.

mm

Preview only — shown in the 3D view. It doesn’t change the parts list.

Fit checkAll rule checks pass: slots, threads, joints and cut lengths. We haven’t built this design ourselves yet.

Parts list · 75

A
HFS6-3030 extrusion (30x30, slot 8)Cut to 718 mm (28.3 in)Model HFS6-3030-718-LTPEnd tap M8 × 24 mm deep at the left end (paid machining). Misumi: order HFS6-3030-718-LTP. Bought elsewhere, the end is not tapped: tap it M8 yourself.Amazon sells fixed lengths: cut it to the length above yourself, or order it cut (and end-tapped where noted) from Misumi.Misumi HFS6-3030-LVerifiedAmazon B09WD7W63DNot verified — check the specs before you buyNot end-tapped: tap it yourselfAmazon B08BC8G36XNot verified — check the specs before you buyNot end-tapped: tap it yourself
× 4
B
HFS6-3030 extrusion (30x30, slot 8)Cut to 600 mm (23.6 in)Model HFS6-3030-600Amazon sells fixed lengths: cut it to the length above yourself, or order it cut (and end-tapped where noted) from Misumi.Misumi HFS6-3030-LVerifiedAmazon B09WD7W63DNot verified — check the specs before you buyAmazon B08BC8G36XNot verified — check the specs before you buy
× 4
C
HFS6-3030 extrusion (30x30, slot 8)Cut to 1540 mm (60.6 in)Model HFS6-3030-1540Amazon sells fixed lengths: cut it to the length above yourself, or order it cut (and end-tapped where noted) from Misumi.Misumi HFS6-3030-LVerifiedAmazon B09WD7W63DNot verified — check the specs before you buyAmazon B08BC8G36XNot verified — check the specs before you buy
× 2
D
Desktop panel (cut to size or bring your own)1600 × 660 × 27 mm (63.0 × 26.0 × 1.1 in)Cut to size or bring your own.No verified US source yet
× 1
E
NFJN8-50 M8 leveling footModel NFJN8-50Misumi NFJN8-50VerifiedAmazon B0F9DTSV3DNot verified — check the specs before you buy
× 4
F
HBLFSN6 die-cast corner bracketModel HBLFSN6Misumi HBLFSN6VerifiedAmazon B0B2ZXPGHDNot verified — check the specs before you buyAmazon B07BQQJWD1Not verified — check the specs before you buy
× 12
G
HNTAP6-6 spring-sheet T-nut M6 (slot 8)Model HNTAP6-6Misumi HNTAP6-6VerifiedAmazon B09J1DPQCFNot verified — check the specs before you buy
× 24
H
M6x12 button head hex socket bolt (ISO 7380)No verified US source yet
× 24

Paid link — we may earn a commission from qualifying purchases. Details

No “Add all to Amazon cart” yet: we haven’t verified any Amazon listing against our specs. Use the Misumi links, or check each Amazon listing before you buy.

We email you once to confirm. Only confirmed addresses count toward making the kit.

Stability estimate does not include the weight of your tabletop. Fixings for your tabletop aren't in this list — attach it to suit your board.

Load. We don’t publish load ratings. This design has not been load-tested by us; what it holds depends on your tabletop, your assembly and how you use it. Don’t stand or sit on it, and test it yourself before trusting it with anything heavy or valuable.

Before you buy. This parts list is generated from the design and checked by our rules; we have not built this table yet. Check each listing against the spec shown here. You build and use it at your own risk — see the Terms.

Letters match the flat-lay view in the 3D preview (tap Parts list). Store links go straight to the seller.

Parts list · 75

Aluminum extrusion table at a glance

SizeSet it above; the parts list and 3D view follow.
Build timeWe haven’t built it ourselves yet, so we don’t list a build time or difficulty.
CostWe don’t show prices; each line of the parts list links to the seller.

How the frame is built

Four 30 × 30 mm (3030) legs stand on M8 leveling feet screwed into the tapped leg ends. Each end of the table is a closed frame: two legs, a top rail and a lower rail running front to back. Two long rails join the two ends under the front and back edges of the top. Every rail end is held by a die-cast corner bracket with two T-nuts and two bolts. The tabletop is a board you cut or bring yourself.

How to use the configurator

  1. Type the width, depth and height you want, in centimeters, or use the sliders. Height is to the top of the tabletop.
  2. Set the tabletop thickness to match your board. The legs get shorter as the board gets thicker, so the height stays what you typed.
  3. Read the fit check. Above 200 cm wide the frame needs a middle leg or a larger profile, which we have not designed yet, so the parts list is blocked at those widths.
  4. Open the parts list. Each letter matches a group in the 3D flat-lay; tap Parts list on the preview to see it.
  5. Copy the link to share or save this exact size.

Use it as an aluminum extrusion workbench

The same frame works as a workbench: set the height you like to work at, the depth of your bench top and a top thickness that matches your board. Nothing else changes — the legs, rails, brackets and feet are the same parts, and the parts list follows your sizes.

What a workbench version does not add: no lower shelf, no extra bracing and no middle leg, and we make no extra load claim for bench use. Bench fixings such as vises, pegboards or clamps are not part of this design.

Load

We don’t publish a load rating for this table or workbench.

FAQ

Can I use this table as a workbench?

Yes. It is the same 3030 frame; set the height, depth and top thickness for your bench. We have not added bench-specific parts or tested it for bench loads.

How much weight does it hold?

We don’t publish a load rating. What it holds depends on your top, your assembly and how you use it.

Can it be wider than 200 cm?

Not yet. Wider frames need a middle leg or a larger profile, which we have not designed, so the fit check blocks those widths.

What tools do I need?

The M6 button-head bolts on the parts list take a 4 mm hex key (ISO 7380-1). We haven’t built this table ourselves yet, so we don’t list other tools.